478B05（483C28）美国PCB供电电源真诚双利
478B05（483C28）美国PCB供电电源真诚双利
478B05:3通道，线路供电，信号条件。对于单端MEMS和电容式传感器，4针输入连接。
| Performance | |||
| Channels | 3 | 3 | |
| Frequency Response (±5 %) | DC Hz | DC Hz | |
| Frequency Response (±5 %) | ≥2000 Hz | ≥2000 Hz | |
| Voltage Gain (±1 %) | 1:1 | 1:1 | |
| Electrical | |||
| Excitation Voltage (±10 %) | 17.3 V | 17.3 V | |
| DC Offset | ±2.25 V | ±2.25 V | |
| Spectral Noise (1 Hz) | 0.50 µV/√Hz | -126 dB | [1] |
| Spectral Noise (10 Hz) | 0.60 µV/√Hz | -124 dB | [1] |
| Spectral Noise (100 Hz) | 0.35 µV/√Hz | -129 dB | [1] |
| Spectral Noise (1000 Hz) | 0.35 µV/√Hz | -129 dB | [1] |
| Spectral Noise (10000 Hz) | 0.075 µV/√Hz | -142 dB | [1] |
| Broadband Electrical Noise (1 to 10000 Hz) | 30 µV | -90 dB | [1] |
| Power Required | DC Power | DC Power | |
| DC Power | +32 to 38 VDC | +32 to 38 VDC | [2] |
| Current Consumption | 0.12 Amps | 0.12 Amps | |
| Physical | |||
| Electrical Connector (Input, sensor) | 4-Pin Jack | 4-Pin Jack | |
| Electrical Connector (Output, scope) | BNC Jack | BNC Jack | |
| Electrical Connector (DC Power Input) | DIN Jack | DIN Jack | |
| Size - Depth | 11 in | 28 cm | |
| Size - Height | 6.3 in | 16 cm | |
| Size - Width | 2.4 in | 6.1 cm | |
| Weight | 2.0 lb | 908 gm | |
English:SI: 483C28:8通道，线路供电，桥接/差分/ICP®传感器信号条件，增量增益，自动调零，以太网
频率范围：（-5%）0.05至50000赫兹
| Performance | |||
| Channels | 8 | 8 | |
| Sensor Input Type(s) | ICP®, Voltage, Bridge/Differential | ICP®, Voltage, Bridge/Differential | |
| Voltage Gain (ICP/Voltage Mode) | x0.1 to x200 | x0.1 to x200 | |
| Voltage Gain (Bridge/Differential Mode) | x0.1 to x2000 | x0.1 to x2000 | |
| Accuracy (Gain, x0.1 to x0.4) | ±5 % | ±5 % | |
| Accuracy (Gain, x0.5 to x0.99) | ±1 % | ±1 % | |
| Accuracy (Gain, x1.0 to x2000) | ±0.5 % | ±0.5 % | |
| Accuracy (Excitation) | ±1 % | ±1 % | |
| Input Range (Differential) | ±0 to 10 V | ±0 to 10 V | |
| Output Range (Minimum) | ±10 V | ±10 V | |
| Frequency Range (-5 %) (≥100 Gain) | 0.05 to 50000 Hz | 0.05 to 50000 Hz | [1] |
| Frequency Range (-5 %) (x100 Gain) | 0.05 to 100000 Hz | 0.05 to 100000 Hz | [1] |
| Phase Response (at 1 kHz) | ±1 ° | ±1 ° | |
| Cross Talk (maximum @ 10kHz) | -72 dB | -72 dB | |
| Calibration (Shunt) | Internal/External | Internal/External | |
| TEDS Sensor Support | Yes | Yes | |
| Fault/Bias Monitor/Meter (LED) | Open/Short/Overload | Open/Short/Overload | |
| Control Interface | |||
| Digital Control Interface | Ethernet | Ethernet | |
| Environmental | |||
| Temperature Range (Operating) | +32 to +120 °F | 0 to +50 °C | |
| Electrical | |||
| Power Required (direct input to unit) | AC Power | AC Power | |
| AC Power (47 to 63 Hz) | 100 to 240 VAC | 100 to 240 VAC | |
| AC Power | ≤0.9 Amps | ≤0.9 Amps | |
| Excitation Voltage (To Sensor) | >+24 VDC | >+24 VDC | |
| Excitation Voltage (Bridge Input ) (Positive) | +0 to 12 V | +0 to 12 V | [2] |
| Excitation Voltage (Bridge Input ) (Negative) | -0 to 12 V | -0 to 12 V | [2][3] |
| Input Imbalance Adjustment (Maximum, Gain <10) | ±2 V | ±2 V | |
| Input Imbalance Adjustment (Maximum, Gain ≥10) | ±0.2 V | ±0.2 V | |
| Common Mode Voltage (Maximum) | ±10 V | ±10 V | |
| DC Offset (Stability, Maximum RTI) | 5 µV/°C | 5 µV/°C | |
| DC Offset (AC Coupled) | ≤50 mV | ≤50 mV | |
| DC Offset (DC Coupled, Gain <100) | <10 mV | <10 mV | |
| DC Offset (DC Coupled, Gain ≥100) | <20 mV | <20 mV | |
| Current Output (Bridge Input ) (Excitation, Maximum) | 30 mA | 30 mA | |
| Constant Current Excitation (To Sensor) | 0 to 20 mA | 0 to 20 mA | |
| Output Impedance | ≤50 Ohm | ≤50 Ohm | |
| Impedance (Input) | >1 MOhm | >1 MOhm | |
| Broadband Electrical Noise (1 to 10000 Hz) (Gain x1) | 50 µV rms | 50 µV rms | [5] |
| Spectral Noise (1 Hz ) (Gain x1) | 6.0 µV/√Hz | 6.0 µV/√Hz | [5] |
| Spectral Noise (10 Hz ) (Gain x1) | 1.5 µV/√Hz | 1.5 µV/√Hz | [5] |
| Spectral Noise (100 Hz ) (Gain x1) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Spectral Noise (1 kHz ) (Gain x1) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Spectral Noise (10 kHz ) (Gain x1) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Broadband Electrical Noise (1 to 10000 Hz) (Gain x10) | 75 µV rms | 75 µV rms | [5] |
| Spectral Noise (1 Hz ) (Gain x10) | 20 µV/√Hz | 20 µV/√Hz | [5] |
| Spectral Noise (10 Hz ) (Gain x10) | 1.5 µV/√Hz | 1.5 µV/√Hz | [5] |
| Spectral Noise (100 Hz ) (Gain x10) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Spectral Noise (1 kHz ) (Gain x10) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Spectral Noise (10 kHz ) (Gain x10) | 1.0 µV/√Hz | 1.0 µV/√Hz | [5] |
| Broadband Electrical Noise (1 to 10000 Hz) (Gain x100) | 350 µV rms | 350 µV rms | [5] |
| Spectral Noise (1 Hz ) (Gain x100) | 140.0 µV/√Hz | 140.0 µV/√Hz | [5] |
| Spectral Noise (10 Hz ) (Gain x100) | 14.0 µV/√Hz | 14.0 µV/√Hz | [5] |
| Spectral Noise (100 Hz ) (Gain x100) | 8.0 µV/√Hz | 8.0 µV/√Hz | [5] |
| Spectral Noise (1 kHz ) (Gain x100) | 4.0 µV/√Hz | 4.0 µV/√Hz | [5] |
| Broadband Electrical Noise (1 to 10000 Hz) (Gain x1000) | 3000 µV/rms | 3000 µV/rms | [4] |
| Spectral Noise (10 kHz ) (Gain x100) | 4.0 µV/√Hz | 4.0 µV/√Hz | [5] |
| Overload Threshold (±0.2 Vpk) | 10 Vpk | 10 Vpk | |
| Physical | |||
| Electrical Connector (ICP® Sensor Input) | BNC Jack | BNC Jack | |
| Electrical Connector (Bridge/Differential) | 8-socket mini DIN | 8-socket mini DIN | |
| Electrical Connector (Output) | BNC Jack | BNC Jack | |
| Electrical Connector (Ethernet) | RJ-45 | RJ-45 | |
| Size - Height (nominal ) | 1.75 in | 44.5 mm | |
 Size - Width (nominal ) | 19.0 in | 482.6 mm | |
| Size - Depth (nominal ) | 13.7 in | 348 mm | |
| Weight | 7.0 lb | 3.18 kg | |
optoforce六分力传感器的详细资料：
匈牙利公司OPTOFORCE公司研发生产的六轴力传感器，多维力传感器，多维力传感器测量，力测量方案，三维力测量，三轴向力传感器，触角传感器，指尖传感器，性价比特别高。
运用： 1.智能搬运 2.机器人手指和机器人腿及整个机器人 3.拉压力测量 4.自动化测量和控制5.风洞试验
1. OMD-10-SA-10N 特点：
测量三维力：10N
精度高，正常精度为1%，特制产品精度高于1%
对化学反应不敏感
产品的设计可按需求调节
防尘防水设计抗高过载设计设计坚固，使用简单明了
可靠性高
低电源消耗
感应表面采用硅橡胶
传感器基座：PCB板
操作温度：PCB基座版：-40度到85度
测量特性：FZ方向可以承受三倍的过载
2.OMD-20-SA-60N
测量三维力:60 N
精度高，正常精度为1%，特制产品精度高于1%
对化学反应不敏感
产品的设计可按需求调节
防尘防水设计
抗高过载设计
设计坚固，使用简单明了
可靠性高
低电源消耗
感应表面采用硅橡胶
传感器基座：金属或ABS（塑料）
操作温度：
塑料基座板：-10度到40度
金属基座版：-40度到85度
测量特性：FZ方向可以承受六倍的过载
3. OMD-30-SA-100N
测量三维力: 100N
精度高，正常精度为1%，特制产品精度高于1%
对化学反应不敏感
产品的设计可按需求调节
防尘防水设计
抗高过载设计
设计坚固，使用简单明了
可靠性高
低电源消耗
感应表面采用硅橡胶
传感器基座：金属或ABS（塑料）
操作温度：
塑料基座板：-10度到40度
金属基座版：-40度到85度
测量特性：FZ方向可以承受六倍的过载
4.OMD-30-FA-1600N
测量三维力: 1600N
精度高，正常精度为1%，特制产品精度高于1%
对化学反应不敏感
产品的设计可按需求调节
防尘防水设计
抗高过载设计
设计坚固，使用简单明了
可靠性高
低电源消耗
感应表面采用硅橡胶
传感器基座：金属（塑料）
操作温度：
金属基座版：-40度到85度
测量特性：
压力范围：1600N
拉力范围：200N
FZ方向可以承受二倍的过载
5. HEX-80-RA-3200 六维力/扭矩（F/T）传感器
精度高，正常精度为1%，特制产品精度高于1%
对化学反应不敏感
产品的设计可按需求调节
防尘防水设计
抗高过载设计
设计坚固，使用简单明了
可靠性高
低电源消耗
感应表面采用高强度的硅橡胶
传感器基座：铝6062
操作温度：
-40度到85度
测量特性：
F(Z+):3200 N
F(X),(Y),(Z):350N
T:10 NM
6.带力反馈的智能旋钮
可以获得以下关键数据：
1. 线性和非线性的弹簧模拟
2. 位置/扭矩/速度
OPTOFORCE 的传感器的以下物理参数可以订制：
1.表面大小和直径 2.表面材料 3.表面外观 4.表面形状 5.测量范围 6.传感器基座 7.传感器安装架
运用：
1.智能搬运 2.机器人手和机器人腿及整个机器人 3.拉压力测量 4.自动化测量和控制 5.风洞试验
我们的地址：上海市金山区吕巷镇干巷荣昌路318号3幢1018室
电话：021-59112701
联系手机： 期待您的咨询
